Siemens A60, C60, etc BZZZZZ on power
...Ok, to understood:
-enter in service mode and send to me log file.
-try to set your contrast (if have low level, your color display is blue).
Goto the Contrast Tab in Joker -> Enter service mode ->Light on -> 5007 -> Read -> Adjust contrast -> 5007 Write
- try to change your display (is the same with C60)....
Is possible to have bad contact or missing connection between the phone microcontroller and display connector. Try to rehot the microcontroller BGA (using the hot air generator). Manny times here is the problem (on the Siemens phones - bad connection between the PCB pads and microcontroller).
dagos
Siemens A60, C60, etc BZZZZZ on power
did u try Contast tool for Siemens,usualy after flash u need to setup contrast level...
and yes u need to do CUT...
du u ewer read old post before u posting ???
Siemens A60, C60, etc BZZZZZ on power
May i know the cut for siemens a60...where is?
Many thanks
Siemens A60, C60, etc BZZZZZ on power
ALL ok.
Mobile now work, but...usually the language...no italian.
The files are:
A62C_070800_xbz.zip 12 4.8 MB 2006-Apr-16
A62_060100_service.zip 10 4.5 MB 2005-Apr-12
A62_069500_service.zip 12 4.3 MB 2005-Apr-12
A62_070100_service.zip 18 4.4 MB 2006-Dec-04
A62_070200_service.zip 5 4.4 MB 2006-Dec-04
A62_070300_service.zip 5 4.4 MB 2006-Dec-04
A62_070400_service.zip 10 4.4 MB 2006-Dec-04
A62_070500_service.zip 13 4.4 MB 2006-Dec-04
A62_070600_service.zip 9 4.4 MB 2006-Dec-04
A62_070700_service.zip 4 4.4 MB 2006-Dec-04
A62_079000_service.zip 4 4.4 MB 2006-Dec-04
A62_079100_service.zip 137 4.4 MB 2006-Dec-04
A62_079200_xbz.zip 272 4.3 MB 2006-Apr-16
A62_079800_xbz.zip
According what said , the A62_079800...means:
A62...mobile
07...firmware
98...????
00...language pack (01...is not present??)
Br,
Moder
Siemens A60, C60, etc BZZZZZ on power
May i know the cut for siemens a60...where is?
Many thanks
Using FREIA...without cut.........this is the log:
FREIA - Engine build 10, Frontend build 9
Thanks goes out for the following:
Maxim, Rolis, Sergey, PapaJoe, Lead,
TheWizard, Jozso (for hardware and cable
support and of course beta testing),
Nico, Victor, Pinker, Tom,
and all the others who supports ...
COMM_LoadBoots : selected phone family is 13
TTY_OpenCOMPort : opening COM1
COMM_IsBootRunning : bootcode does not seem to be running
COMM_LoadBoots : Waiting to power on the phone ...
COMM_LoadBoots : phone is powered on
COMM_SendBoot : boot file is not accepted
Moder
Siemens A60, C60, etc BZZZZZ on power
Hi dagos,
i specify that each time i make something on the mobile, it makes BZZZZ.
Said this, these following are the logs regarding each point you request:
SERVICE MODE:
Start...
Loading ServiceBoot...
Sending ServiceBoot Ok.
MobileMode: Service
HWID: 132 (MC60)
MC60 lg95 Sw05 17.09.03 12:23:47
IMEI: ************
DisplayID: 34, Sharp Hynix HM17CM4101
FSN: 26655A03
SW FlashID: 0001/2212
Code(05): OTP closed
Code(09): BootKEY is written in EEPROM
Code(0D): Keys are registered in BCORE
Code(13): Complete access to BFB
Code(15): Complete condition
Code(19): Monitoring is switched on
Code(1D): Blocks 5121,5122,5123 are present
Battery Voltage 3776 mV.
SecurityMode: Factory
THE CONTRAST:
this is the value
44,48,0,0
When i try to read it makes BZZZ, and after several times the result and the new settings:
Read Contrast...
No Ping mobile
Read Contrast...
No Ping mobile
Read Contrast...
Display1 contrast: 44, 48
Display2 contrast: 0, 0
Test Contrast 94...
No Ping mobile
Test Contrast 94...
No Ping mobile
Test Contrast 94...
Write contrast (94, 95) in block 5007...
Write block 5007 - Ok.
Display1 contrast: 94, 94
Display2 contrast: 95, 95
After this, the mobiles work, but DISPLAY is always "Blu"
Br, Moder
Siemens A60, C60, etc BZZZZZ on power
I have the cable "For SIM C55" and port rs232.....infact when i try to read, appear that message on Joker.
Moder
Siemens A60, C60, etc BZZZZZ on power
then change display if phone works fine this models have a bad displays regards
Siemens A60, C60, etc BZZZZZ on power
try here
http://eh.student.utwente.nl/~landy/
pass:
mobile
elibom
Siemens A60, C60, etc BZZZZZ on power
Hi guys,
when i try to turn on the mobiles SIEMENS A62, the mobile make "bzzzzz" and than turn off automatically.
I know, i've to do the FULLFLASH, but after downloading files, i watched that some are for 8mb and other for 16mb.
So....how can i unsterstand if i need the ff for 8mb instead of 16mb?
I have these files:
A62_16MB_Repair_FF.rar
a62_full_0604.rar
a62_v06.rar
A62v07_8MB_Repair_FF.rar
which is the file i must use???
Br, Moder
PS:::: this is the log of mobile
SERVICE MODE
Start...
Loading ServiceBoot...
Sending ServiceBoot Ok.
MobileMode: Service
HWID: 231 (A62)
A62 lg98 Sw07 16.05.05 15:08:56
IMEI: ******************
DisplayID: 37, Philips Epson S1D15G14
FSN: 3944D507
SW FlashID: 0001/220C
Code(05): OTP closed
Code(09): BootKEY is written in EEPROM
Code(0D): Keys are registered in BCORE
Code(13): Complete access to BFB
Code(15): Complete condition
Code(19): Monitoring is switched on
Code(1D): Blocks 5121,5122,5123 are present
Battery Voltage 3780 mV.
SecurityMode: Factory
DEL INSTANCES
Instance Format...
Delete Instance "Voice Memo" - None.
Delete Instance "Voice Dialing" - None.
Delete Instance "Browser Cache" - None.
Delete Instance "File System" - Ok.
Delete Instance "Tegic" - None.
Delete Instance "Address Book" - Ok.
ReStart Phone!
Instance Format...
Delete Instance "Voice Memo" - None.
Delete Instance "Voice Dialing" - None.
Delete Instance "Browser Cache" - None.
Delete Instance "File System" - Ok.
Delete Instance "Tegic" - None.
Delete Instance "Address Book" - Ok.
ReStart Phone!
DEFRAG EEP
Backup EEPROM blocks...
HWID: 231 (A62)
EELITE Info: free buffer 55540 bytes, free at all 55572 bytes, free for deleted 55572 bytes.
EEFULL Info: free buffer 87012 bytes, free at all 87224 bytes, free for deleted 21832 bytes.
Read All EELITE blocks from 1 to 285 ...
Read All EEFULL blocks from 5000 to 5439 ...